DLXB PH-RX-CL / M dosing pump with integrated pH / Rx / CL controller

DLXB PH-RX-CL / M dosing pump with integrated pH / Rx / CL controller (optional)

  • Productivity: 1 ÷ 20 l/hr.
  • Pressure: 2 ÷ 10 bar.

The dosing pump DLXB PH-RX-CL/M is a microprocessor-based multifunctional dispenser with an integrated controller of the pH (acid/base balance) , RedOx (the redox potential of Rx) and CL (free chlorine).

The dosing pump DLXB PH-RX-CL/M is used to dispense liquid reagents, it monitors and regulates the level of pH, RedOx, Cl liquids.

Measuring ranges
- pH level 0-14 with a resolution of 0.01 pH
- RedOx level -1000 to +1400 mV s 1 mV resolution
- CL level 0-20 ppm with 0.1 ppm resolution

Before setting the operating mode, one of the three measured parameters must be selected: pH, RedOx or Cl. Program the installation point (digital value of the selected parameter level) and the metering direction (more/less relative to the installation point).

Dosage regimens:

- Manual . In this mode, the performance is set in the range from 0 to 100%. The pump will dispense at the set capacity and will stop when the set point is reached.

- Proportional « PROP » . In PROP mode. sets the point of maximum performance in the range from 0 to 100%. The pump will run at maximum frequency until this point is reached, after which it will start proportional dosing. The processor will automatically monitor performance and stop the pump at the installation point. When the level differs from the installation point, the pump will start dosing again.

Additional functions: calibration of sensors, setting of 4-20 mA output, alarm, thermal compensation (when the corresponding PT100 sensor is connected), setting the delay time for switching on and the time for continuous dosing, applying a password, completely or partially restarting the pump.

  • Metering pump with integrated pH/RedOx/Cl controller (optional).
  • Dosing modes: proportional to PROP. or permanent ON/OFF.
  • Measurement range: 0-14 pH; -1000 + 1400 mV; 0-20 ppm (mg/L).
  • Backlit LCD.
  • Three status indicators.
  • 5 touch buttons for selecting pump operating modes.
  • 4-20 mA output.
  • ON/OFF relay output for alarms.
  • Automatic temperature compensation (with PT100 temperature sensor).
  • Support for flow sensors and level sensors (not included).

External dimensions DLXB PH-RX-CL/M

External dimensions DLXB PH-RX-CL/M

DLXB PH-RX-CL/M Performance Diagrams

    

DLXB PH-RX performance diagrams -CL/M

TECHNICAL SPECIFICATIONS

                                                                                                                                                                                                                                                                                                                                

Type Consumption Pressure Article Price without VAT, (€)
l/hour bar pH-Rx-Cl/M
0115 1 15 PBX272225E 492
2 10
3 5
0220 2 20 PBX2703201 579
0507 5 7 PBX270385E 492
6 5
8 2
0810 8 10 PBX272285E 528
10 7
12 3
1504 15 4 PBX272315E 552
2003 20 3 PBX2722001 578
  • 120V - +10%
  • R/C - +60 euro

The dispenser is made in a polypropylene case, degree of protection IP65 (dust, splashes). New sample dispenser head with manual air bleed valve.

The pump control panel with a convenient interface 5 touch control buttons, a menu in the basic and advanced versions and 3 LED indicators of the status of work. All programmable parameters are displayed on the LCD. Sticker control panel coating UV protective film.

Appearance of DLXB PH-RX-CL/M pump control panels

Appearance of panels pump control DLXB PH-RX-CL/M

Options DLXB PH-RX-CL/M

Each DLXB PH-RX-CL/M pump comes standard with the following:

  1. Dosing pump (1 pc.).
  2. Flexible PVC intake hose (4 meters).
  3. Discharge hose (2 meters).
  4. Intake valve (1 pc.).
  5. Injection valve (1 pc.).
  6. Passport instruction (1 pc.).

DLXB PH-RX-CL/M pump installation example

DLXB pump installation measures DLXB PH-RX-CL/M