Automatic Water Disinfection Systems - POOL GUARD 3 PH / CL (SCLO3 HYCHLOR)

Automatic water treatment station POOL GUARD 3 PH / CL (pH, Cl, T °), with an amperometric SCLO3 HYCHLOR chlorine sensor.

POOL GUARD 3 PH / CL (SCLO 3 HYCHLOR) - an automatic proportional dosing system and control the level of PH and CL (concentration of free chlorine in water) for swimming pools up to 500 m 3 . The dosing station is controlled by a fluid flow sensor (included), in the absence of flow, the system goes into standby mode.

Pool Guard 3 PH / Cl automatic water treatment station - provides pool water treatment by: measuring and regulating free chlorine (inorganic chlorine only) - dosing of chlorine, measuring and regulating pH (pH) , measuring the flow of water to shut off the outputs in the absence of flow. A temperature sensor (PT100) allows the temperature compensation to be automatically taken into account by the controller.

The station is equipped with two interconnected diaphragm pumps (DLX PH-RX-CL / MB 5-7 230V) with integrated pH / Rx / Cl controllers. The pumps are equipped with a graphical TFT-display with 3 LEDs (power supply, pulse frequency, level sensor or alarm) and non-volatile memory, built-in control of the level and flow of the reagent. Data entry and control is carried out using 5 control buttons on the front of the pumps. All main probes and sensors are installed in the SCLO 3 HYCHLOR flow cell. A connecting cable with adapter is used to connect the chlorine sensor to the DLX (B) PH-RX-Cl / MB (M) metering pump.

The dosing system POOL GUARD 3 PH / CL (SCLO 3 HYCHLOR) is supplied mounted on a chemical-resistant plastic panel (450x600x8 mm), in a complete set, ready for installation and commissioning.

TECHNICAL DATA:

  • The system is based on DLX PH-RX-CL / M dosing pumps with built-in pH / Rx / Cl controllers (optional) and an SCLO 3 HYCHLOR flow-free ammeter free flow sensor.
  • Alarm on the time of continuous dosing, followed by shutdown of the dosing pumps.
  • Dosing delay when the system is turned on.
  • Level sensor or flow sensor alarm.
  • Alarm settings for pH / Cl (MIN / MAX) concentration limits.
  • Dosing modes: constant ON / OFF and proportional PROP.
  • Fine-tuning proportional mode.
  • Lock the settings made by password.
  • Menu selection: Basic / Full.
  • Set hysteresis.
  • Pump productivity: 5 l / h - 7 bar.
  • Measuring ranges: 0-14 pH; 0-5 ppm (mg / L).
  • Protection class (of pumps): IP65.
  • Support for flow sensor and reagent level sensor.

DOSING SYSTEM CONFIGURATION: (SCLO 3 HYCHLOR) - with SCLO 3 HYCHLOR amperometric free chlorine sensor (inorganic chlorine only).

Built-in functions:

  • Alarm on the time of continuous dosing, followed by shutdown of the dosing pumps.
  • Dosing delay when turning on the station.
  • Alarm and shutdown of the station by flow or reagent level sensors in canisters.
  • Alarm settings for chemical limits pH / Cl reagents (MIN / MAX levels).
  • Dosing modes: constant "ON / OFF" and proportional to "PROP".
  • Set hysteresis.
  • The dosing station is controlled by a liquid flow sensor (included), if there is no flow, the system goes into standby mode « STAND BY », with subsequent indication on the LCD displays of the pumps.

Inputs / Exits :

- pH / RX inputs - BNC connectors, input impedance > 10 ^ 12 Ω.
- Input Cl - 4-pin connector.
- 2 inputs "LEV" for level sensor SPDT pin 5 V / 5 mA.
- Input "FLOW "flow sensor (SPDT pin 5 V / 5 mA).
- 4-20 mA output.
- ON / OFF relay output for alarm.

Composition of the dosing system POOL GUARD 3 PH / CL [SCLO HYCHLOR]

2 pcs. - DLX pump PH-RX-CL / M 5-7 230V PVDF
1 pc. - PH level sensor with 0.5 m cable.
1 pc. - chlorine sensor SCLO 3 HYCHLOR
1 pc. - cable with adapter for SCLO 3 HYCHLOR chlorine sensor
2 pcs. - reagent level sensor with 2 m cable.
1 pc. - mounting kit for SCLO 3 HYCHLOR chlorine sensor
1 pc. - set of installation and maintenance instructions
1 pc. - calibration solution PH 7, 55ML
1 pc. - calibration solution PH 9, 55ML
2 pcs. - reagent injection valve
2 pcs. - reagent intake valve
2 pcs. - reagent intake hose, 4x6, PVC, 2 mp.
2 pcs. - reagent discharge hose, 4x6, PE, 2 m.p.
1 pc. - mounting plate 450x600x8 mm

Type Performance,
l / h
Pressure,
bar
pH CL Price without VAT, (€)
POOL GUARD 3 PH / CL
(SCLO3 HYCHLOR)
5 7 0 … 14 0-5 ppm 2250